Nikon 1

Nikon 1 AW1 Firmware - A firmware: Ver. 1.10, B firmware: Ver. 1.10

Modifications include:

- Support for the FULL/LIMIT focus limit switch on the 1 NIKKOR VR 70-300mm f/4.5-5.6 has been added.
When camera firmware is updated to this version, autofocus does not function when an FT1 running L firmware Ver. 1.10 or earlier is used.
Users of the FT1 must update FT1 L firmware to Ver. 1.10 at the same time camera firmware is updated.
- An issue that prevented reading of .MOV data contained in folders numbered 256 or higher on the memory card inserted in the camera by an application such as the Wireless Mobile Utility used to connect a device via PTP/IP has been resolved.
- An Underwater flash option has been added to the shooting menu to support use of the Underwater Speedlight SB-N10.
- An issue that caused images captured using a non-CPU lens with the Mount Adapter FT1 to be underexposed has been resolved.
Link- http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8209


Nikon 1 J3 Firmware - A firmware: Ver. 1.20, B firmware: Ver. 1.20

Modifications include:

- Support for the FULL/LIMIT focus limit switch on the 1 NIKKOR VR 70-300mm f/4.5-5.6 has been added.
When camera firmware is updated to this version, autofocus does not function when an FT1 running L firmware Ver. 1.10 or earlier is used.
Users of the FT1 must update FT1 L firmware to Ver. 1.20 at the same time camera firmware is updated.
- An issue that sometimes caused a card access error to be displayed when a Lexar UHS-I SD memory card was inserted in the camera has been resolved.
- An issue that prevented wireless shooting via the WU-1b (Wireless Mobile Adapter) when the Digiscoping Adapter DSA-N1 for Nikon 1 cameras was used, or when manual focus was used with an AF-S lens mounted via the Mount Adapter FT1, has been resolved.
- An issue that prevented reading of .MOV data contained in folders numbered 256 or higher on the memory card inserted in the camera by an application such as the Wireless Mobile Utility used to connect a device via PTP/IP has been resolved.
- An issue that prevented adjustment of magnification for manual focus display from "Focus mode" > "Manual focus" in the shooting menu when a manual focus lens was used has been resolved.
Link- http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8206

Nikon 1 J2 Firmware - A firmware: Ver. 1.20, B firmware: Ver. 1.20 Modifications include:

- Support for the FULL/LIMIT focus limit switch on the 1 NIKKOR VR 70-300mm f/4.5-5.6 has been added.
When camera firmware is updated to this version, autofocus does not function when an FT1 running L firmware Ver. 1.10 or earlier is used.
Users of the FT1 must update FT1 L firmware to Ver. 1.20 at the same time camera firmware is updated.
- An issue that prevented printing of photos using the PictBridge standard with some printers has been resolved.
Link- http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8215

Nikon 1 S1 Firmware - A firmware: Ver. 1.20, B firmware: Ver. 1.20 Modifications include:

- Support for the FULL/LIMIT focus limit switch on the 1 NIKKOR VR 70-300mm f/4.5-5.6 has been added.
When camera firmware is updated to this version, autofocus does not function when an FT1 running L firmware Ver. 1.10 or earlier is used.
Users of the FT1 must update FT1 L firmware to Ver. 1.20 at the same time camera firmware is updated.
- An issue that sometimes caused a card access error to be displayed when a Lexar UHS-I SD memory card was inserted in the camera has been resolved.
- An issue that prevented wireless shooting via the WU-1b (Wireless Mobile Adapter) when the Digiscoping Adapter DSA-N1 for Nikon 1 cameras was used, or when manual focus was used with an AF-S lens mounted via the Mount Adapter FT1, has been resolved.
- An issue that prevented reading of .MOV data contained in folders numbered 256 or higher on the memory card inserted in the camera by an application such as the Wireless Mobile Utility used to connect a device via PTP/IP has been resolved.
- An issue that prevented adjustment of magnification for manual focus display from "Focus mode" > "Manual focus" in the shooting menu when a manual focus lens was used has been resolved.
Link- http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8221

Nikon 1 J1 Firmware - A firmware: Ver. 1.40, B firmware: Ver. 1.40 Modifications include:

- Support for the FULL/LIMIT focus limit switch on the 1 NIKKOR VR 70-300mm f/4.5-5.6 has been added.
When camera firmware is updated to this version, autofocus does not function when an FT1 running L firmware Ver. 1.10 or earlier is used.
Users of the FT1 must update FT1 L firmware to Ver. 1.20 at the same time camera firmware is updated.
- An issue that prevented printing of photos using the PictBridge standard with some printers has been resolved.
Link- http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8218

Nikon 1 V1 Firmware - A firmware: Ver. 1.40, B firmware: Ver. 1.40 Modifications include:

- Support for the FULL/LIMIT focus limit switch on the 1 NIKKOR VR 70-300mm f/4.5-5.6 has been added.
When camera firmware is updated to this version, autofocus does not function when an FT1 running L firmware Ver. 1.10 or earlier is used.
Users of the FT1 must update FT1 L firmware to Ver. 1.20 at the same time camera firmware is updated.
- An issue that prevented printing of photos using the PictBridge standard with some printers has been resolved.
Link- http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8203

Nikon 1 V2 Firmware - A firmware: Ver. 1.20, B firmware: Ver. 1.20 Modifications include:

- Support for the FULL/LIMIT focus limit switch on the 1 NIKKOR VR 70-300mm f/4.5-5.6 has been added.
When camera firmware is updated to this version, autofocus does not function when an FT1 running L firmware Ver. 1.10 or earlier is used.
Users of the FT1 must update FT1 L firmware to Ver. 1.20 at the same time camera firmware is updated.
- An issue that caused images captured using the Mount Adapter FT1 with continuous shooting at 15 fps to be underexposed has been resolved.
- An issue that sometimes caused a card access error to be displayed when a Lexar UHS-I SD memory card was inserted in the camera has been resolved.
- An issue that prevented wireless shooting via the WU-1b (Wireless Mobile Adapter) when the Digiscoping Adapter DSA-N1 for Nikon 1 cameras was used, or when manual focus was used with an AF-S lens mounted via the Mount Adapter FT1, has been resolved.
- An issue that prevented reflection of the exposure compensation setting when the Mount Adapter FT1 was used with shooting in Motion Snapshot shooting mode and Scene auto selector exposure mode has been resolved.
- An issue that prevented reading of .MOV data contained in folders numbered 256 or higher on the memory card inserted in the camera by an application such as the Wireless Mobile Utility used to connect a device via PTP/IP has been resolved.
Link- http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8200

DSLR
Nikon D800E Firmware - A firmware: Ver. 1.10, B firmware: Ver. 1.10

Modifications include:

- Custom Setting f13 has been changed to "Assign Movie Record Button"**.

- With Custom Setting f13 changed to "Assign Movie Record Button, Assign MB-D12 AF-ON" is now Custom Setting f14.

- Custom Setting "f15: Assign Remote Fn Button" has been added**.

- The following functions have been added or renamed when the D800E is used with the Communication Unit UT-1 running firmware Ver. 2.0. A "Network (UT-1)" option has been added to, and Wireless transmitter has been renamed "Wireless transmitter (WT-4)" in, the setup menu.

Function that has been added:
i. "HTTP server" mode
Use to view the pictures on the camera memory card, or to take photographs, from the web browser on a computer or iPhone.

Functions that have been renamed:
i. "FTP upload" mode (previously Transfer mode (FTP)) Use to upload photos and movies from camera memory cards, or to upload photos as they are taken, to an ftp server.
ii. "Image transfer" mode (previously Transfer mode (PC)) Use to upload photos and movies from camera memory cards, or to upload photos as they are taken, to a computer.
iii. "Camera control" mode (previously PC mode) Use to control the camera from a computer running Camera Control Pro 2 (available separately) and save photos and movies directly to the computer.
*To enable support for these functions, Communication Unit UT-1 firmware must be updated to Ver. 2.0 or later, and the Wireless Transmitter Utility must be updated to Ver. 1.5.0 or later. When camera firmware is updated, network profiles specified with earlier firmware versions cannot be used. Network profiles must be created again.

- Support for the updated version of Communication Unit UT-1 firmware has been added.

- Support for CompactFlash memory cards with capacities greater than 128 GB has been added.

- When "AF-ON" only was selected for Custom Setting a4 ("AF activation") and the AF-ON button was pressed to initiate autofocus during viewfinder photography, focus remained locked even after the user took their finger off the button, and the shutter could be released at any time. However, specifications have been modified so that the shutter cannot be released under the following conditions if the camera fails to focus**.
i. Autofocus mode is set to "AF-S" (single-servo AF) ii. AF-area mode is set to "Single-point AF"
iii. Custom Setting a2 ("AF-S priority selection") is set to "Focus"

- When values for 12 or 18 lenses were stored with "AF fine-tune" > "Saved value" in the setup menu, only some of the lenses for which values had been stored were displayed under "List saved values". This issue has been resolved.

- When the live view selector was set to live view photography with Custom Setting g4 ("Assign shutter button") set to "Record movies", a value for preset manual white balance could not be measured. This issue has been resolved.

- When the built-in flash was set to Commander mode, remote Speedlights sometimes did not fire. This issue has been resolved.

- In some rare cases, the memory card access lamp remained lit for longer than usual, and some time was required before any operations could be performed. This issue has been resolved.

Link- http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8236


Nikon D800 Firmware - A firmware: Ver. 1.10, B firmware: Ver. 1.10

Modifications include:
- Custom Setting f13 has been changed to "Assign Movie Record Button"**.

- With Custom Setting f13 changed to "Assign Movie Record Button, Assign MB-D12 AF-ON" is now Custom Setting f14.

- Custom Setting "f15: Assign Remote Fn Button" has been added**.

- The following functions have been added or renamed when the D800 is used with the Communication Unit UT-1 running firmware Ver. 2.0. A "Network (UT-1)" option has been added to, and Wireless transmitter has been renamed "Wireless transmitter (WT-4)" in, the setup menu.

Function that has been added:
i. "HTTP server" mode
Use to view the pictures on the camera memory card, or to take photographs, from the web browser on a computer or iPhone.

Functions that have been renamed:
i. "FTP upload" mode (previously Transfer mode (FTP)) Use to upload photos and movies from camera memory cards, or to upload photos as they are taken, to an ftp server.
ii. "Image transfer" mode (previously Transfer mode (PC)) Use to upload photos and movies from camera memory cards, or to upload photos as they are taken, to a computer.
iii. "Camera control" mode (previously PC mode) Use to control the camera from a computer running Camera Control Pro 2 (available separately) and save photos and movies directly to the computer.
*To enable support for these functions, Communication Unit UT-1 firmware must be updated to Ver. 2.0 or later, and the Wireless Transmitter Utility must be updated to Ver. 1.5.0 or later. When camera firmware is updated, network profiles specified with earlier firmware versions cannot be used. Network profiles must be created again.

- Support for the updated version of Communication Unit UT-1 firmware has been added.

- Support for CompactFlash memory cards with capacities greater than 128 GB has been added.

- When "AF-ON" only was selected for Custom Setting a4 ("AF activation") and the AF-ON button was pressed to initiate autofocus during viewfinder photography, focus remained locked even after the user took their finger off the button, and the shutter could be released at any time. However, specifications have been modified so that the shutter cannot be released under the following conditions if the camera fails to focus**.
i. Autofocus mode is set to "AF-S" (single-servo AF) ii. AF-area mode is set to "Single-point AF"
iii. Custom Setting a2 ("AF-S priority selection") is set to "Focus"

- When values for 12 or 18 lenses were stored with "AF fine-tune" > "Saved value" in the setup menu, only some of the lenses for which values had been stored were displayed under "List saved values". This issue has been resolved.

- When the live view selector was set to live view photography with Custom Setting g4 ("Assign shutter button") set to "Record movies", a value for preset manual white balance could not be measured. This issue has been resolved.

- When the built-in flash was set to Commander mode, remote Speedlights sometimes did not fire. This issue has been resolved.

- In some rare cases, the memory card access lamp remained lit for longer than usual, and some time was required before any operations could be performed. This issue has been resolved.

Link- http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8224

Communication Unit UT-1 Firmware Ver. 2.0 Modifications include:

- The following functions have been added or renamed when the UT-1 is used with the D800 or D800E running A and B firmware Ver. 1.10.
Function that has been added:
i. HTTP server mode
Use to view the pictures on the camera memory card, or to take photographs, from the web browser on a computer or iPhone.
Functions that have been renamed:
ii. FTP upload mode (previously Transfer mode (FTP)) Use to upload photos and movies from camera memory cards, or to upload photos as they are taken, to an ftp server.
iii. Image transfer mode (previously Transfer mode (PC)) Use to upload photos and movies from camera memory cards, or to upload photos as they are taken, to a computer.
iv. Camera control mode (previously PC mode) Use to control the camera from a computer running Camera Control Pro 2 (available separately) and save photos and movies directly to the computer.

Link- http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8227

COOLPIX
Nikon COOLPIX S3000 Firmware Ver. 1.3

Modifications include:
- An issue, that in some very rare cases prevented the battery from charging, has been resolved.

Link- http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8233

Nikon COOLPIX S5200 Firmware Ver. 1.2
Modifications include:
- Occurrence of an issue that sometimes causes loud sounds to be distorted with movie recording when "Wind noise reduction" is set to "On" has been reduced.
Link- http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8230

Views: 238

Reply to This

Replies to This Discussion


FW: New firmware update: COOLPIX P600 and COOLPIX P340

 
 
5:11 PM
 
 
To: Ian Leggatt


Kind regards,
Ian Leggatt
Purchasing Manager
Diamonds Camera, Video and Digital l Photographic Wholesalers
165 Rundle St, Adelaide SA 5000
p. (08) 8224-0665 - option 2: f. (08) 8223-1253

-----Original Message-----
From: Geoff.Mellor@nikon.com [mailto:Geoff.Mellor@nikon.com]
Sent: Monday, 20 October 2014 4:51 PM
Subject: New firmware update: COOLPIX P600 and COOLPIX P340

Hi Guys,

Please see below for the new firmware updates.

Nikon COOLPIX P600 Firmware Ver. 1.2

Modifications include:

- An issue that prevented charging of the Rechargeable Li-ion Battery EN-EL23 using the camera and charging AC adapter when the EN-EL23 was completely discharged has been resolved.

Link: http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8402


Nikon COOLPIX P340 Firmware Ver. 1.2

Modifications include:

- An issue that prevented charging of the Rechargeable Li-ion Battery EN-EL12 using the camera and charging AC adapter when the EN-EL12 was completely discharged has been resolved.
- When RAW (NRW) images captured with a burst of continuous shooting at a setting of Continuous H were opened in image-processing software such as ViewNX 2 for development, image colours were abnormal. This issue has been resolved.

Link: http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8399
Please see below firmware updates for the D750 and D810.

Nikon D750 Firmware: Ver. 1.01
http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8448


Nikon D810 Firmware: Ver. 1.02
http://nikonasia-en.custhelp.com/app/answers/detail/a_id/8451

Reply to Discussion

RSS

 

© 2017   Created by Jassa.   Powered by

Badges  |  Report an Issue  |  Terms of Service